RAM 6000 Specifikace Strana 1

EverServ Series 6000 USERS GUIDE Copyright ParTech Inc. PN770501016

10SPECIFICATIONS FEATURES Description Part Number PROCESSORS: 1.73 GHz Celeron M F7110 2.0 GHz Core Duo F7111 2.16 GHz

11 Crew Side Pedestal - Optical Finger Print F7871 Customer Side Panel (Opaque) F7880 Point of Promotion Lens (Clear) F7881 Graphic

12BIOS Introduction This user manual describes the AMI BIOS setup program and configuration options of the EverServ motherboard. The BIOS setup progr

 Exit Selects exit options and loads default settings The following sections completely describe the configuration options found in the menu items a

Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. Î System Date [xx/xx/xx]

CPU Configuration Use the CPU Configuration menu to view detailed CPU specifications and configure the CPU. BIOS Menu 3: CPU Configuration The CPU Co

IDE Configuration Use the IDE Configuration menu to change and/or set the configuration of the IDE devices installed in the system. BIOS Menu 4: IDE

IDE Master, IDE Slave Use the IDE Master and IDE Slave configuration menu to view both primary and secondary IDE device details and configure the IDE

18Auto-Detected Drive Parameters The “grayed-out” items in the left frame are IDE disk drive parameters automatically detected from the firmware of t

19Î Disabled BIOS is prevented from using Multi-Sector Transfer on the specified channel. The data to and from the device occurs one sector at a t

2PAR warrants its products to be free of manufacturing defects. Please refer to the back of the sales contract for warranty terms and conditions.

20of 33.3MBps Î UDMA3 Ultra DMA mode 3 selected with a maximum data transfer rate of 44MBps (To use this mode, it is required that an 80-conductor

Super IO Configuration Use the Super IO Configuration menu to set or change the configurations for the FDD controllers, parallel ports and serial port

22Î 3E8/IRQ4 Serial Port 2 I/O port address is 3E8 and the interrupt address is IRQ4 Î 2E8/IRQ3 Serial Port 2 I/O port address is 2E8 and the int

Hardware Health Configuration The Hardware Health Configuration menu shows the operating temperature, fan speeds and system voltages. BIOS Menu 7: Ha

ACPI Configuration The ACPI Configuration menu configures the Advanced Configuration and Power Interface (ACPI) and Power Management (APM) options. BI

APM Configuration The APM Configuration menu configures the Advanced Power Management (APM) options. 25

Event Log Configuration Use the Event Log Configuration menu to view or delete the system event log storing POSt and run-time errors and events. BI

MPS Configuration Use the MPS Configuration menu to select the multi-processor table. BIOS Menu 10: MPS Configuration Î MPS Function [Enabled] Us

USB Configuration Use the USB Configuration menu to read USB configuration information and configure the USB settings. BIOS Menu 11: USB Configuratio

29Î Legacy USB Support [Enabled] The Legacy USB Support BIOS option refers to USB mouse and USB keyboard support. Normally if this option is not ena

3INTRODUCTION ...

PCI/PnP Use the PCI/PnP menu to configure advanced PCI and PnP settings. WARNING! Setting wrong values for the BIOS selections in the PCIPnP BIOS me

31Î Yes This setting allows the operating system to change the interrupt, I/O, and DMA settings. Set this option if the system is running Plug and P

Boot Use the Boot menu to configure system boot options. BIOS Menu 13: Boot 32

Boot Settings Configuration Use the Boot Settings Configuration menu to configure advanced system boot options. BIOS Menu 14: Boot Settings Configurat

34 Î Bootup Num-Lock [On] Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be modified during boot up. Î Off Does n

Boot Device Priority Use the Boot Device Priority menu to specify the boot sequence from the available devices. Possible boot devices may include: 

Security Settings Use the Security Settings menu to set passwords for supervisor/user. Î Supervisor Password [Not Installed] Î User Password [Not

Chipset Use the Chipset menu to access the North Bridge and South Bridge configuration menu. WARNING! Setting the wrong values for the Chipset BIOS

North Bridge Configuration Use the North Bridge Configuration menu to configure the North Bridge chipset. BIOS Menu 16:NorthBridge Chipset Configurat

Video Function Configuration Use the Video Function Configuration menu to configure the video device connected to the system. SouthBridge Configurati

4INTRODUCTION This guide provides information about the EverServ System. It is presented in five parts as outlined in the table below. Introduction

Exit Use the Exit menu to load default BIOS values, optimal failsafe values and to save configuration changes. BIOS Menu 17:Exit Î Save Changes an

ENERGY STAR QUALIFIED COMPUTERS OVERVIEW ♦ Depending on usage, an ENERGY STAR qualified computer will use up to 50% less energy. ♦ Your office can s

42APPENDIX A Separating PPC from POS 1. Loosen the (2) thumbscrews under the Panel POS (operator side) which secure the cover over the main board I

Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test m

44SAFETY ♦ Before connecting cables or devices to connector wells, please turn off the power first thus preventing potential ESD damage. ♦ The se

45PAR PHONE NUMBERS Service USA: 800.382.6200 Canada: 800.387.4963 Parts USA: 800.PAR.PART Canada: 800.387.4963 Sales Continental USA except

EQUIPMENT DESCRIPTION POS REGISTER Item Description 1. LCD display A screen that shows programming or order information. 2. Power indicator Shows

Item Description 6. Customer Display Shows the customer the order total, tax total, and any change due. It may also show preset advertisement infor

7CONNECTOR WELLS Item Description 1. Audio Jacks Connects to cables from speaker left, speaker right, and headphone. 2. COMM serial port 1 (RS-23

32 1 4514 13 12 8611109 7 8

PEDESTAL CONNECTOR WELLS Item Description 1. Power Receptacle Connects to power cable. 2. KVS Receptacle Connects to KVS cable. 3. USB 24V @ 2